Understanding double layer media

Although Double Layer 8.5GB DVD-ROM and DVD video discs have been available for some time as part of the DVD read-only standard, it was thought impossible or at least improbable that a similar technology could be developed for personal DVD recording.

However, Mitsubishi Kagaku Media (MKM), parent company of Verbatim Corp., and Philips have recently proven that a Double Layer DVD recording system is feasible utilizing the DVD+R (write-once) format. This technology is named Double Layer DVD+R, or DVD+R DL. DVD+R DL hardware and media products will enable consumers to store up to four hours of DVD-quality video, 16 hours of VHS video quality or 8.5GB of data on a single disc — without having to stop and turn the disc.

The development of reliable DVD+R DL media materials and manufacturing processes is the key technology enabler for Double Layer DVD+R recording. This white paper discusses each component of the DVD+R DL media structure and the challenges involved in producing compatible DVD+R DL media.

Double Layer Disc Structure

The basic challenge was to develop materials and manufacturing processes for multi-layer DVD+R DL discs that allow the properties of two unique layers, once recorded, to meet the DVD read-only specifications for DVD-ROM drives and DVD video players. During recording (and reading), each layer can be targeted without disrupting data on the other layer (see Figure 1). The first recording layer (L0) of the Verbatim DVD+R DL disc is semi-transparent, providing enough reflectivity for writing/reading data on the first layer, yet transmitting enough laser power to read/write on the second layer (L1) by refocusing the laser. In addition to optimizing layer reflectivity, new Metal Azo recording dyes were developed by MKM for each layer to optimize parameters such as signal amplitudes and power margins and ensure compatibility with current DVD standards.

Note: Due to the loss of light at the L0 interface, a high-power laser is needed to transmit enough light to L1. Higher-power (30 mW) lasers, sufficient for Double Layer recording, have recently been implemented in 8X speed single-layer DVD+R recorders.

The write/read laser passes through Substrate 1 (S1) while accessing Layer 0 and Layer 1. The groove shape that is molded into S1 must be very accurate to properly guide recording on L0. In addition, the thickness of S1 must be uniform throughout the disc. Due to the addition of the spacer material between L0 and L1, the thickness of S1 is thinner than single-layer 4.7GB DVD media. Under this condition, it is difficult to form accurate groove shapes while maintaining the proper thickness uniformity.

This technology has overcome this difficulty by applying very precise substrate molding technology and developing stampers. The quality of S1 cannot be optimized without internal mastering and stamper-making capabilities and expertise.

First Dye Recording Layer (L0)

L0 should function as a high-quality recording layer and should also transmit enough light to L1. For high-quality recording, L0 must exhibit high sensitivity, a wide power margin, low jitter and high durability. However, due to the transmittance requirement to enable recording on L1, L0 must also exhibit “low absorbency of light.” These requirements are difficult to achieve because, in general, high sensitivity and low light absorbance have a trade-off relationship.

The only way to solve this issue is to develop and fine-tune a new recording dye.

Semi-transparent Metal Reflector (R0)

This layer plays the important role of reflective layer for L0 – but must transmit enough light to read/write on L1. To provide stable reflective and transmitted light, the thickness of R1 must be precisely controlled.

Spacer

The optically transparent layer between R0 and L1 is called the spacer. The groove for L1 recording is formed in the spacer layer and it is very important to minimize any noise caused by the spacer. Spacer thickness uniformity must be tightly controlled for clear recording on L1.

Second Dye Recording Layer (L1)

L1 is recorded via light transmitted through S1, L0, R0, and the spacer. Although each of these layers is designed to have excellent transmission performance, the light energy reaching L1 will be reduced. Thus, high sensitivity is the most critical requirement for L1.

A newly developed, highly sensitive Metal Azo dye has been implemented for L1 to realize a well-defined data mark recorded with the relatively low level of transmitted laser power.

Metal Reflector (R1)

The metal reflector for L1 must be designed for high reflectivity to maximize the light returned to the DVD recorder for proper signal detection.

The R1 material and thin film sputtering processes have been optimized to create a highly reflective and uniform R1.

Read/Write performance

The most important objective for DVD+R DL media is to maintain read compatibility with existing DVD-ROM drives and DVD video players. As a result, a recorded DVD+R DL disc must meet the specifications for dual-layer DVD-ROM media.

Conclusion

The construction of a Double Layer DVD+R disc is complicated. Reflectivity, transmission and absorption of both recording layers must be balanced.

Would you recommend this article?

Share

Thanks for taking the time to let us know what you think of this article!
We'd love to hear your opinion about this or any other story you read in our publication.


Jim Love, Chief Content Officer, IT World Canada

Featured Download

Related Tech News

Featured Tech Jobs

 

CDN in your inbox

CDN delivers a critical analysis of the competitive landscape detailing both the challenges and opportunities facing solution providers. CDN's email newsletter details the most important news and commentary from the channel.